YMS PAINT Over 20 years experience in the production of customized industrial paint coatings

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 1

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 2

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 3

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 4

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 5

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 6

Polyurethane Anti-static Paint for Inner Walls of Oil Tank

Film Thickness:

60um dry film thickness (about 133um wet film thickness)

Theoretical Spreading Rate:

6.25m²/Kg (50um dry film thickness)

Full Cure:

(23±2℃ )24h

Flash Point:

27℃

Color:

Black, Gray

Usage:

no gloss

Density:

~1.2 Kg/L

Solid Volume:

(45±2 )%

Shelf Life:

12 months

To Touch, Minutes@23±2 °C:

To Handle, Hours@23±2 °C:

4 hour

Inquiry

Write a Review

PRODUCT DESCRIPTION

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 7

This two-component product is made up of hydroxyl resin, isocyanate adduct, conductive pigments and fillers, auxiliaries, anti-static agents, solvents, etc. It’s essential that this paint is resistant to various petroleum products but has no impact on oil quality. Moreover, with great conductivity, its film can prevent accidents caused by electrostatic accumulation during the storage and transportation. In addition, it should be applied four times continuously with dry film thickness 150 μ m, and film resistivity less than 105 ohm · cm

Typical Uses:

This product is designed to protect the internal walls of crude oil tank, oil product tanks, oil storage tank and oil pipeline against corrosion.

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 8

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 9

Application Guide

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 10

● Mixing:

Use the power mixer to mix the main paint evenly, and then as you stir it, you add the hardener until you get to mix well.

● Mixing Ratio:

Part A: Part B=20:5 (by weight)

● Thinner:

Exclusive thinner.

● Airless Spray:

Nozzle tip: 0.018~0.025 inches.

Spray pressure: 18~25 MPa.

Thinner ratio: 0~15% (by weight of paint).

● Brush, Roller:

Recommended for small areas only.

Must achieve required thickness.

DRYING SCHEDULE

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 11

Substrate temperature	10 °C	20 °C	30 °C
To touch (30μm)	2h	1h	30min
To handle (30μm)	8h	4h	3h
Min. recoating time	8h	4h	3h
Max. recoating time	-	-	-
Pot life	4h	2h	1h
* Make sure no chalking and other contaminations before recoating.
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation condition.

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 12

SURFACE TREATMENT

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 13

All surfaces to be coated shall be clean and dry. The surface shall be evaluated and treated according to ISO8504 standard.
Bare steel: sandblasting to Sa2.5(IOS8501-1:2007). For the non-soaking site, acceptable for power tool grinding, at least reach St2(IOS8501-1:2007).

Steel painted work shop primer: apply to clean, dry, intact and approved primer.
Painted surface: only apply to clean, dry and intact compatible primer.

APPLICATION

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 14

Application conditions: Substrate temperature shall be at 3℃ higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 15

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 16

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 17

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 18

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 19

CLASSICAL COATING SYSTEM

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 20

Please inquiry JIANBANG Paint for specific coating solutions.

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 21

Polyurethane Anti-rust Primer: 2*60µm (dry film thickness)

.Service 01

Polyurethane Anti-static Paint: 2*30µm (dry film thickness)

SAFETY AND HEALTH

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 22

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

Please handle used paint barrel correctly to avoid any pollution.

Storage:

Store this product in shady, dry, ventilated and away from heat sources warehouse. Storage temperature above 0℃, the shelf life is 12 months at room temperature. If exceeding shelf life, the products shall be tested before using.

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 23

Packaging	Packing size	Packing weight
Part A	20L	20 KG
Part B	5L	4 KG

Certificate

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 24

CE Certificate

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 25

Environmental Management Syatem ISO14001 New

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 26

Occupational Health And Safety Management System OHSAS 18001 New

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 27

Quality Management System ISO 9001 New

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 28

ROHS Report

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 29

SASO1

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 30

sgs1

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 31

sgs2

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 32

SRC

Polyurethane Anti-static Paint for Inner Walls of Oil Tank 33

Get in touch with us

YMS Industrial paint suppliers core products, including anti corrosive paint, antirust paint, acid & alkali resisting paint, heat resisting paint, building & floor paint etc., help protect and extend substrate life for years.