Oriented by technology, we serve customers worldwide not only our high quality products, but also technical consultation and engineering scenarios.
PRODUCT DESCRIPTION
This product is a two-component coating composed of high elastic special rubber, modified resin, high quality pigment and filler, auxiliary agent, cross-linking agent etc. Meanwhile, by solvent volatilization this product can form a continuous, rich elastic, tough and durable protective film. Besides, the coating film has excellent physical and mechanical properties, heat resistance, cold resistance, etc. Furthermore, it can keep its elasticity for a long time when the temperature is between 25℃ and 80℃.
Typical Uses:
This product can be used for the surface of cement mortar, concrete, asbestos cement board, etc. Besides, it is especially designed for the maintenance and protection of internal and external walls with cracks.
Application Guide
● Mixing:
Use the power mixer to mix the main paint evenly, and then as you stir it, you add the hardener until you get to mix well.
● Mixing Ratio:
Part A: Part B= 5:1 (by weight).
● Thinner:
Elastic exterior wall coating special thinner
● Airless Spray:
Nozzle tip:0.017~0.023 inch.
Spray pressure:15~18 MPa.
Thinner ratio:0~15% (by weight of paint).
●Brush, roller:
Recommended must achieve required thickness.
Substrate temperature | 10 °C | 20 °C | 30 °C |
To touch (20μm) | 2h | 0.5h | 20min |
To handle (20μm) | 24h | 24h | 18h |
Min. recoating time | 2h | 0.5h | 20min |
Min. recoating time | / | / | / |
Pot Life | 4h | 2h | 1h |
* Make sure no chalking and other contaminations before recoating. | |||
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation conditions. |
SURFACE TREATMENT
Surface treatment of each base layer: The quality of the coated cement slurry and concrete base layer shall comply with JGJ73-91 construction and acceptance specifications for building decoration engineering.
The surface of the substrate must be clean, dry, solid, free from oil and other dirt. The PI value is less than 10. If there is an old coated wall, the loose, peeled, powdered coating should be removed and smoothed with sandpaper.
In the case of moldy walls, wash the wall with 25% bleach hot water, leave the washing liquid on the surface for 10 minutes, then rinse thoroughly with water, dry for 48 hours before painting. Surface pock and crevices should be coated with the company's construction materials putty. It is necessary to construct the treated wall as soon as possible after drying to avoid reontamination.
Solvent-Based Sealing Primer: 1*20µm (dry film thickness)
Exclusive Putty For Architectural Paint: 1~2mm (dry film thickness)
Elastic Outdoor Solvent-Based Paint: 2*30µm (dry film thickness)
SAFETY AND HEALTH
Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.
Please handle used paint barrel correctly to avoid any pollution.
Storage:
Store this product in shady, dry, and ventilated warehouse. The shelf life is 12 months at room temperature. If exceeding shelf life, the products shall be tested before using.
Disclaimer:
All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.
Packaging | Packing size | Packing weight |
Part A | 20L | 20 KG |
Part B | 5L | 4 KG |
Copyright © 2020 Changzhou IMS New Materials Technology Co., Ltd. | All Rights Reserved | XML
Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.