Oriented by technology, we serve customers worldwide not only our high quality products, but also technical consultation and engineering scenarios.
PRODUCT DESCRIPTION
The product is composed of acrylic copolymer emulsion, high quality pigment and a variety of additives. Meanwhile, it has excellent resistance to alkali , water, washing and mildew. Besides, this coating has the advantages of strong adhesion, simple construction, quick drying, non-toxicity and safety.
Typical Uses:
The product is designed for the substrate surface such as the concrete, cement mortar and plaster. Besides, it is also suitable for the interior wall decoration of civil residential and public buildings.
Application Guide
● Mixing:
Ready to use.
● Thinner:
Clean water
● Airless spray:
Nozzle tip: 0.017~0.023 inches
Spray pressure: 15~18Mpa
Thinner ratio:0~10% (by weight of paint)
● Brush, Roller:
Recommended
Must achieve required thickness
Substrate temperature | 10°C | 20°C | 30°C |
To touch(20um) | 4h | 2h | 1.5h |
To handle(20um) | 24h | 24h | 20h |
Min. recoating time | 24h | 24h | 20h |
Max. recoating time | - | - | - |
* Make sure no chalking and other contaminations before recoating. | |||
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation conditions, humidity, mechanical strength,etc. |
SURFACE TREATMENT
vSurface treatment of each base course: the quality of the cement slurry and concrete base course shall conform to JGJ73-91 code for construction and acceptance of building decoration engineering. The base surface must be clean, dry, firm, free of grease and other dirt, with a PI value less than 10. If have the metope of old besmear film, answer will loose, fall off, the besmear film that powdery is cleared clean, grind with sandpaper level off. In case of mildew on the wall, wash with 25% bleach in hot water. Leave the washing solution on the surface for 10 minutes. Then rinse surface thoroughly with clean water, surface should dry for 48 hours before applying. The surface and gap should be coated with the company's construction materials special putty wipe flat. After the treatment of the wall, the wall should be dry as soon as possible after the construction, so as to avoid re-pollution.
Classic Coating System
Advanced Construction Latex Coating Sealing Primer
1*20 µm (dry film thickness)
Advanced Exterior Wall Putty
1~2 mm (dry film thickness)
Advanced Construction Latex Finish Paint
2*60 μm(dry film thickness)
SAFETY AND HEALTH
Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.
Please handle used paint barrel correctly to avoid any pollution.
Storage:
Store this product in shady, dry, and ventilated warehouse. Storage temperature above 0℃, the shelf life is 12 months at room temperature. If exceeding shelf life, the products shall be tested before using.
Disclaimer:
All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.
Packing size | Packing weight |
20L | 20KG |
Copyright © 2020 Changzhou IMS New Materials Technology Co., Ltd. | All Rights Reserved | XML
Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.