loading

YMS PAINT Over 20 years experience in the production of customized industrial paint coatings

Waterborne Epoxy Tough Floor Paint1 1
Waterborne Epoxy Tough Floor Paint1 2
Waterborne Epoxy Tough Floor Paint1 3
Waterborne Epoxy Tough Floor Paint1 4
Waterborne Epoxy Tough Floor Paint1 5
Waterborne Epoxy Tough Floor Paint1 1
Waterborne Epoxy Tough Floor Paint1 2
Waterborne Epoxy Tough Floor Paint1 3
Waterborne Epoxy Tough Floor Paint1 4
Waterborne Epoxy Tough Floor Paint1 5

Waterborne Epoxy Tough Floor Paint1

    oops...!

    no product data.

    Go to homepage

    PRODUCT DESCRIPTION

    Waterborne Epoxy Tough Floor Paint1 6

    The water-based two-component floor paint is mainly based on water-borne epoxy resin and curing agent. It contains low VOC and no solvent odor. Besides, this paint creates a tough and high-gloss finish. The main advantages of this floor paint are strong resistance to acid, oil, water and impact. Moreover, it also has good resistance to abrasion, electrostatic, mildew and stain.

    Typical Uses:

    This product is designed for a wide range of floors with various levels of mechanical and chemical exposure. It also used in industrial floor applications including garage,parking lot, electronics factory and hospital. What’s more, it is widely used for office building, laboratory, food and beverage factory.

    Waterborne Epoxy Tough Floor Paint1 7
    Waterborne Epoxy Tough Floor Paint1 8

    Application Guide

    Waterborne Epoxy Tough Floor Paint1 9

    ● Mixing:

    Use the power mixer to mix the main paint evenly, and then as you stir it, you add the hardener until you get to mix well. Generally, if the temperature below 10 ℃, it needs 20 min induction time; if the temperature over 10℃, it needs 15 min induction time.

    ● Mixing Ratio:

    Part A: Part B= 20: 4 (by weight).

    ● Thinner:

    DI water or tap water.

    ● Spray, brush, roller:

    Recommended for small areas only. Must achieve required thickness.

    DRYING SCHEDULE

    Waterborne Epoxy Tough Floor Paint1 10

    Substrate temperature

    10 °C

    20 °C

    30 °C

    To touch (1mm)

    4h

    2h

    1h

    To handle (1mm)

    24h

    12h

    6h

    Min. recoating time

    16h

    8h

    4h

    Max. recoating time

    10h

    7h

    5h

    Pot life

    1.5h

    1h

    0.5h

    * Make sure no chalking and other contaminations before recoating.

    * Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation condition.

    Waterborne Epoxy Tough Floor Paint1 11

    SURFACE TREATMENT

    Waterborne Epoxy Tough Floor Paint1 12

    All surface to be coated shall be clean and dry. The surface shall be evaluated and treated according to ISO8504 standard.

    Steel: Sanding to Sa2.5 (ISO8501-1:2007). It is acceptable to polish by power tools to meet at least St2.0(ISO8501-1:2007).

    Concrete surface treatment:

    a. First of all, it is necessary to confirm whether reliable damp-proof facilities are installed below the concrete base. The new concrete or cement base should be cured for at least 28 days, and its moisture content should not exceed 5%. The moisture content of the base should be evaluated by empirical method.

    b. The base surface should be clean, solid and pollution-free, such as slurry and paint splashing, curing agent, grease and so on. For excessive float pulp, it is better to first use slight roughing, polishing, oil-stained ground, using electric angle grinder to polish.

    c. The cracks and empty drum on the floor surface should be repaired first.

    d. Whatever method is used to treat the surface, a clean, solid and dry base surface must be obtained. It is especially important that the grassroots should not be in a state of rising tide.

    e. The base layer is cleaned and sanded with a sander.

    APPLICATION

    Waterborne Epoxy Tough Floor Paint1 13

    Application conditions: Substrate temperature shall be at 5 ℃ higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.

    Waterborne Epoxy Tough Floor Paint1 14
    Waterborne Epoxy Tough Floor Paint1 15
    Waterborne Epoxy Tough Floor Paint1 16
    Waterborne Epoxy Tough Floor Paint1 17
    Waterborne Epoxy Tough Floor Paint1 18

    CLASSICAL COATING SYSTEM

    Waterborne Epoxy Tough Floor Paint1 19

    Please inquiry JIANBANG Paint for specific coating solutions.

    Waterborne Epoxy Tough Floor Paint1 20

    Waterborne Epoxy Sealing Primer: 0.1mm ( thickness)

    Waterborne Epoxy Floor Putty: 1mm ( thickness)

    Waterborne Epoxy Floor Paint: 1mm ( thickness)

    SAFETY AND HEALTH

    Waterborne Epoxy Tough Floor Paint1 21

    Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

    Please handle used paint barrel correctly to avoid any pollution.

    Storage:

    Store this product in shady, dry, and ventilated warehouse away from fire and heat. The shelf life is 12 months at room temperature.

    Disclaimer:

    All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.

    Waterborne Epoxy Tough Floor Paint1 22

    Packaging

    Packing size

    Packing weight

    Part A

    20L

    20 KG

    Part B

    6L

    5 KG

    Certificate

    Waterborne Epoxy Tough Floor Paint1 23

    Waterborne Epoxy Tough Floor Paint1 24
    CE Certificate
    Waterborne Epoxy Tough Floor Paint1 25
    Environmental Management Syatem ISO14001 New
    Waterborne Epoxy Tough Floor Paint1 26
    Occupational Health And Safety Management System OHSAS 18001 New
    Waterborne Epoxy Tough Floor Paint1 27
    Quality Management System ISO 9001 New
    Waterborne Epoxy Tough Floor Paint1 28
    ROHS Report
    Waterborne Epoxy Tough Floor Paint1 29
    SASO1
    Waterborne Epoxy Tough Floor Paint1 30
    sgs1
    Waterborne Epoxy Tough Floor Paint1 31
    sgs2
    Waterborne Epoxy Tough Floor Paint1 32
    SRC
    Get in touch with us
    YMS Industrial paint suppliers core products, including anti corrosive paint, antirust paint, acid & alkali resisting paint, heat resisting paint, building & floor paint etc., help protect and extend substrate life for years.
    Related Products
    no data
    Our fundamental product range, which encompasses rust-resistant industrial paints, paints with acid and alkali resistance, high-temperature-resistant paints, building and floor paints, and so on, aids in safeguarding the substrates while prolonging their lifespan for several years to come.
    Contact with us
    Tel: 0086-17312895118
    Fax: +86-519-85506198

    Address:
    No.2 Building 12, Hengsheng Technology Park II, No.8, Beitanghe Road, anning District, Changzhou, Jiangsu, China
    Copyright © 2025 YMS Paints - www.jianbangcoatings.com | Sitemap
    Customer service
    detect