Widely Applied Epoxy Mica Iron Oxide Intermediate Paint

这里可以自定义设置

PRODUCT DESCRIPTION

This product is a two-component coating composed of high solid content based on epoxy resin and low VOC thick paste type coating polyamide curing agent. It has excellent physical properties such as inter-layer adhesion, flexibility, wear resistance and impact resistance, low VOC, and has excellent acid and alkali resistance, water resistance, oil resistance and chemical resistance.

Typical Uses:

It is used for epoxy coating, suitable for various environments, such as offshore facilities, petrochemical plants, bridges, pulp mills, power plants, and also for the protection of concrete structures in the epoxy system.

这里可以自定义设置

Application Guide

● Mixing:

Use the power mixer to mix the main paint evenly, and then add the hardener and stir until it is well mixed. Generally speaking, when the temperature is below 10℃, 30min will be waited before you use it; 15min when it is above 10℃.

● Mixing ratio:

Part A: Part B=24:4(by weight)

● Thinner:

Epoxy paint thinner

● Airless spray:

Nozzle tip: 0.018~0.027 inches

Spray pressure: 15~18Mpa

Thinner ratio: 5~15% (by weight of paint)

● Brush, Roller:

Recommended for small areas only.

Must achieve required thickness.

DRYING SCHEDULE

Substrate temperature	10°C	20 °C	30°C
To touch(40um)	4h	2h	1h
To handle(40um)	48h	24h	16h
Min. recoating time	56h	6h	4h
Pot life	6h	4h	2h
* Make sure no chalking and other contaminations before recoating.
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation condition.

这里可以自定义设置

SURFACE TREATMENT

All surfaces to be coated shall be clean and dry. The surface shall be evaluated and treated according to ISO8504 standard.
For bare steel, it shall be sandblasted to reach Sa2.5(iso8501-1:2007) standard. Depending on the environment of the non-immersed part, grinding with power tools is acceptable but shall at least reach St2(iso8501-1:2007) standard.
For shop primed steel, the shop primer shall be clean, dry and approved.
For surface painted coatings, this product can apply only to clean, dry and good compatible primer.

APPLICATION

Application conditions: Substrate temperature shall be at 3 ℃higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.

这里可以自定义设置

CLASSICAL COATING SYSTEM

Please inquiry JIANBANG Paint for specific coating solutions.

Classic Coating System

Epoxy Zinc Rich Primer------ 2*40 µm (dry film thickness)

Epoxy Mica Iron Oxide intermediate paint------2*75 µm (dry film thickness)

Acrylic Polyurethane Finish ------2*40 µm (dry film thickness)

这里可以自定义设置

SAFETY AND HEALTH

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.
Please handle used paint barrel correctly to avoid any pollution.

Storage:

Store this product in shady, dry, and ventilated warehouse. Under room temperature, the shelf life is 12 months. If exceeding shelf life, the products shall be tested before using.

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.

	Packing size	Packing weight
Part A	20L	24KG
Part B	5L	4KG

Certificate

CE Certificate
Environmental Management Syatem ISO14001 New
Occupational Health And Safety Management System OHSAS 18001 New
Quality Management System ISO 9001 New
ROHS Report
SASO1
sgs1
sgs2
SRC