Advanced Elastic Outdoor Latex Paint Can Be Used For Concrete...

这里可以自定义设置

PRODUCT DESCRIPTION

This product is a kind of environmental friendly waterborne paint, which is composed of elastic acrylic copolymer compound with UV cross-linking and solidity function, high-quality pigments, fillers, and various additives. This durable and washable coating can keep its elasticity in the temperature range of - 20 ℃ ~ + 40 ℃ for a long time, so as to cover the wall cracking and make the coating protected and anti-leakage. What’s more, with its cross-linking and solidity, the coating has special performance in resisting contaminants, water, acid rain, muggy, and it will ensure the neatness and cleanness of the wall.

Typical Uses:

This product can be used for concrete, cement mortar, plaster and other substrate especially for the maintenance and protection of walls with cracks(≤1.5mm).

这里可以自定义设置

Application Guide

● Mixing:

Ready to use.

● Thinner:

Clean water

● Airless spray:

Spray 0.6m/min pressure：0.3~0.6 MPa

Nozzle tip diameter: 4-10mm, after touch dry, use a smooth rubber roll to flatten the convex surface

● Brush, Roller:

Recommended to be used with spraying

● Scraping:

Must achieve required thickness

DRYING SCHEDULE

Substrate temperature	10°C	20°C	30°C
To touch(30um)	4h	1h	40min
To handle(30um)	24h	24h	20h
Min. recoating time	24h	1h	40min
Max. recoating time	-	-	-
* Make sure no chalking and other contaminations before recoating.
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation conditions, humidity, mechanical strength,etc.

这里可以自定义设置

SURFACE TREATMENT

The quality of cement mortar and concrete base shall conform to JGJ73-9Construction acceptance code for architectural decoration engineering. With the PH value less than 10, the base surface must be clean, dry, solid and free from oil and other dirt. In case of old coating film wall, the loose, detached and powder coating shall be removed. Besides, the surface shall be smooth by burnished. In case of wall with mildew, wash the wall with hot water containing 25% bleach, and leave the detergent on the surface for 10 minutes. Then rinse the surface thoroughly with clean water, and coat it after drying for 48 hours. In addition, use the exclusive putty for construction materials of the company to fill the gap and smooth the rough surface. Furthermore, please paint after the wall is dry as soon as possible to avoid re-contamination.

APPLICATION

Application conditions: Substrate temperature shall be 3 ℃ higher than dew point with relative humidity below 85%. Measurement of temperature and humidity should be conducted close to substrate.

这里可以自定义设置

CLASSICAL COATING SYSTEM

Please inquiry JIANBANG Paint for specific coating solutions.

Classic Coating System

Advanced Construction Latex Coating Sealing Primer

1*20 µm (dry film thickness)

Advanced Exterior Wall Putty

1~2 mm (dry film thickness)

Advanced Construction Latex Finish Paint

2*60 μm(dry film thickness)

这里可以自定义设置

SAFETY AND HEALTH

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. With low VOC volatilization, this coating is waterborne, safe and environmental friendly. Specific security measures depend on the construction and working environment. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

Please handle used paint barrel correctly to avoid any pollution.

Storage:

Store this product in shady, dry, and ventilated warehouse away from heat sources. At room temperature, the shelf life is 12 months. If exceeding shelf life, the product shall be tested qualified before using.

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, so it is not completely correct. Although we try to keep the validity of our advice, we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.