loading

YMS paint manufacturers started in 2001, specialized in the production of customized  coatings. | YMS Paint the professional Industrial Paint Suppliers, Anti Corrosive Paint Manufacturer.

METAL PAINT

Oriented by technology, we serve customers worldwide not only our high quality products, but also technical consultation and engineering scenarios.

Home  > PRODUCTS  > Metal Protection Paint  > 

Anti-corrosive aviation marking paint for concrete chimney and telegraph pole

这里可以自定义设置
Anti-corrosive aviation marking paint for concrete chimney and telegraph pole
B站不支持收货地址
B站不支持库存规格
Color:
Bright red, white
Usage
Flat
Density:
~1.3Kg/L (after mixing)
Solid Volume:
(50±2 )%
Theoretical Spreading Rate:
6.4m²/Kg (50um dry film thickness)
Film Thickness:
60um dry film thickness (about 120um wet film thickness)
Full Cure:
(23±2℃ )24h
Flash Point:
27℃
Shelf Life:
12 months
To Touch, Minutes@23±2 °C:
1h
To Handle, Hours@23±2 °C:
4 h
Pot Life, Hours@23±2℃ :
2h
参数暂无数据
多属性暂无数据
B站不支持优惠卷

Add success, do you want to check your shopping cart?

暂无分享
B站不支持产品保障
该产品后台详情无内容
这里可以自定义设置

PRODUCT DESCRIPTION

This two-component product is mainly composed of hydrogenated acrylic resin, added with silicon modified resin, sun-resistant pigments, fillers, additives, curing agent, organic solvent, etc. It is provided with excellent resistance to weathering, various corrosion, water, heat, cold, ion radiation, etc. With bright film, the product has great light and color retention as well as outstanding construction performance. On top of that, the fast-drying paint can be applied at low temperature.

 

Typical Uses:

This product is widely used to mark and protect concrete chimney, transmission pole and other high-altitude structures.

这里可以自定义设置
这里可以自定义设置

Application Guide

● Mixing: 

rReady to use.

● Thinner: 

Acrylic thinner

● Airless Spray:

Nozzle tip: 0.017~0.023 inch.

Spray pressure: 15~18 MPa.

Thinner ratio: 0~15% (by weight of paint).

● Brush, Roller:

Recommended.

Must achieve required thickness.

DRYING SCHEDULE 

Substrate temperature

10 °C

20 °C

30 °C

To touch (30um)

2h

1h

30min

To handle (30um)

8h

4h

3h

Min. recoating time

8h

4h

3h

Max. recoating time---
Pot life4h2h1h

* Make sure no chalking and other contaminations before recoating.

* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation condition, humidity, mechanical strength,etc.

这里可以自定义设置

SURFACE TREATMENT

 

The surface to be coated shall be clean, dry and free from contaminations. Also, the surface shall be evaluated and treated according to ISO8504 standard.
Bare steel: sandblasting to reach Sa2.5(IOS8501-1:2007). For the non-soaking site, acceptable for power tool grinding, at least reach St2(IOS8501-1:2007).
Steel painted shop primer: apply to clean, dry, intact and approved primer.
Painted surface: only apply to clean, dry and intact compatible primer.
Surface treatment for concrete:
A: For the concrete base floor, first ensure reliable moisture-proof facilities are set below the base concrete. New concrete or the cement base shall be cured for at least 28 days with moisture content not exceeding 5%. The moisture content shall be evaluated empirically.
B: The surface of the base shall be clean, firm and free from contaminants such as mortar paint splashes, curing agent, grease, etc. It’s better to roughly polish the excessive floating pulp and grind the oily ground with electric angle grinder.
C: Defects such as cracks and drums shall be repaired first.
D: The surface shall be clean, firm and dry whatever methods are used to treat it. Above all, the surface shall not be in the state of rising moisture.
E: The base layer shall be cleaned and burnished with a grinder.

APPLICATION 

Application conditions: Substrate temperature shall be at 3 ℃ higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.

这里可以自定义设置

CLASSICAL COATING SYSTEM

Please inquire JIANBANG Paint for specific coating solutions.

Epoxy Primer / Chlorinated Rubber Primer 

30µm (dry film thickness)

Aviation Marking Paint  

2*30µm (dry film thickness)

这里可以自定义设置

SAFETY AND HEALTH

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

Please handle used paint barrel correctly to avoid any pollution.

 

Storage:

Store this product in shady, dry, and ventilated warehouse away from fire and heat. The shelf life is 12 months at room temperature.

 

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance. 


Packing size

Packing weight

Part A20L20KG
Park B

5L

4KG

Certificate

  • CE Certificate
    CE Certificate
  • Environmental Management Syatem ISO14001 New
    Environmental Management Syatem ISO14001 New
  • Occupational Health And Safety Management System OHSAS 18001 New
    Occupational Health And Safety Management System OHSAS 18001 New
  • Quality Management System ISO 9001 New
    Quality Management System ISO 9001 New
  • ROHS Report
    ROHS Report
  • SASO1
    SASO1
  • sgs1
    sgs1
  • sgs2
    sgs2
  • SRC
    SRC

PRODUCT MESSAGE

社媒暂无评论

RELATED PRODUCTS

Chat Online 编辑模式下无法使用
Leave Your Message inputting...
We will get back to you asap