Anti-static Exclusive Anti-corrosive Paint For Oil Tank

这里可以自定义设置

PRODUCT DESCRIPTION

This product is based on the corrosion-resistant epoxy resin and amino resin. Meanwhile, this paint is composed of composite conductive fillers, anti-static agents and additives. Furthermore, it has excellent adhesion, flexibility, impact and oil resistance. What’s more, this coating is suitable for crude oil, 95/130 aviation gasoline, aviation kerosene ,40# engine oil, 120# gasoline, etc. In addition, it has no effect on the quality of oil (glial ≤7 mg/100mg), the film has electrical conductivity, which can prevent oil products from accidents caused by electrostatic accumulation during storage and transportation.

Typical Uses:

This paint is designed for the anti-static and anti-corrosion protection for the inner wall of the storage tanks and cabin which are loaded with crude oil, gasoline, aviation oil, kerosene, etc. Besides, this product can also be used in other application areas where electrostatic coating is required.

这里可以自定义设置

Application Guide

● Mixing:

Use the power mixer to mix the main paint evenly, and then as you stir it, you add the hardener until you get to mix well.

● Mixing Ratio:

Part A: Part B= 20: 5 (by weight).

● Thinner:

Anti-static exclusive thinner

●Airless spray:

Nozzle tip：0.017~0.023 inches

Spray pressure：15~18 MPa

Thinner ratio：0~15% (by weight of paint)

● Brush、Roller:

Recommended

Must achieve required thickness.

DRYING SCHEDULE

Substrate temperature	10 °C	20 °C	30 °C
To touch (1mm)	2h	1h	30min
To handle (1mm)	8h	4h	3h
Min. recoating time	8h	4h	3h
Max. recoating time
Pot life	4h	2h	1h
* Make sure no chalking and other contaminations before recoating.
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation condition.

这里可以自定义设置

SURFACE TREATMENT

All surfaces to be coated shall be clean and dry. The surface shall be evaluated and treated according to ISO8504 standard.

Steel: Sanding to Sa2.5 (ISO8501-1:2007). It is acceptable to polish by power tools to meet at least St2.0 (ISO8501-1:2007).

Steel coated with workshop primer: make sure workshop primer surface is clean, dry and undamaged.

Coated surface: applied on clean, dry and undamaged primer only.

APPLICATION

Application conditions: Substrate temperature shall be at 3^oC higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.

这里可以自定义设置

CLASSICAL COATING SYSTEM

Please inquiry JIANBANG Paint for specific coating solutions.

Epoxy Sealing Primer: 1*30 µm (dry film thickness)

Epoxy Putty: 1~2mm (dry film thickness)

Anti-static Solvent-free Self-leveling Epoxy Floor Paint: 1*1mm(dry film thickness)

这里可以自定义设置

SAFETY AND HEALTH

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. The coating is a water-based coating. Water-based solvent has mild eye irritation, upper respiratory tract irritation, long-term close contact with dry skin, etc. Proper ventilation and precautionary measures must be in place. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

Please handle used paint barrel correctly to avoid any pollution.

Storage:

Store this product in shady, dry, and ventilated warehouse. The shelf life is 12 months at room temperature. If exceeding shelf life, the products shall be tested before using.

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.