Anti-static Paint For Inner Wall Of Oil Pipeline

这里可以自定义设置

PRODUCT DESCRIPTION

This product is composed of epoxy resin, corrosion-resistant filler, composite conductive material. Meanwhile, this paint also has anti-electric agents and additives. What’s more, the anti-static coating for the inner wall of oil pipeline has high strength and can withstand the wear of high velocity fluid. In addition, it has good toughness, anti-rust resistance, oil resistance, physical mechanical properties, etc. Furthermore, the anti-static coating for the inner wall of oil pipeline can prevent the characteristics of electrostatic accumulation.

Typical Uses:

This paint is designed for the anti-static and anti-corrosion protection for the inner wall of the storage tanks and cabin which are loaded with crude oil, gasoline, aviation oil, kerosene etc. Besides, this product can also be used in other application areas with electrostatic coating.

这里可以自定义设置

Application Guide

● Mixing:

Use the power mixer to mix the main paint evenly, and then as you stir it, you add the hardener until you get to mix well.

● Thinner:

Thinner for anti-static paint on inner wall of oil pipeline

● Airless Spray:

Nozzle tip: 0.025~0.031inches

Spray pressure: 18~28Mpa

Thinner ratio: 0~15% (by weight of paint

● Brush, Roller:

Recommended

Must achieve required thickness

DRYING SCHEDULE

Substrate temperature	10 °C	20 °C	30 °C
To touch (30μm)	24h	12h	6h
To handle (30μm)	16h	8h	4h
Min. recoating time	10d	7d	5d
Max. recoating time	6h	4h	2h
* Make sure no chalking and other contaminations before recoating.
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation condition.

这里可以自定义设置

SURFACE TREATMENT

All surfaces to be coated shall be clean and dry. The surface shall be evaluated and treated according to ISO8504 standard.

Steel: Sanding to Sa2.5 (ISO8501-1:2007). It is acceptable to polish by power tools to meet at least St2.0 (ISO8501-1:2007).

Steel coated with workshop primer: make sure workshop primer surface is clean, dry and undamaged.

Coated surface: applied on clean, dry and undamaged anti-static primer only.

APPLICATION

Application conditions: Substrate temperature shall be at 3 ℃ higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.

这里可以自定义设置

CLASSICAL COATING SYSTEM

Please inquiry JIANBANG Paint for specific coating solutions.

Classic Coating System

Chlorosulfonated Polyethylene Anti-corrosion Primer------ 2*40µm (dry film thickness)

Chlorosulfonated Polyethylene Anti-corrosionIntermediatePrimer------2*80µm (dry film thickness)

Chlorosulfonated Polyethylene Anti-corrosion Finish------ 2*30µm (dry film thickness)

这里可以自定义设置

SAFETY AND HEALTH

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. The coating is a water-based coating. Water-based solvent has mild eye irritation, upper respiratory tract irritation, long-term close contact with dry skin, etc. Proper ventilation and precautionary measures must be in place. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

Please handle used paint barrel correctly to avoid any pollution.

Storage:

Store this product in shady, dry, and ventilated warehouse. The shelf life is 12 months at room temperature. If exceeding shelf life, the products shall be tested before using.

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.