Compound Relief Latex Liquid Coating Intermediate Paint

这里可以自定义设置

PRODUCT DESCRIPTION

This product is composed of acrylic copolymer emulsion, silica sol, pigment, filler and a variety of additives. Meanwhile, it has moderate consistency, good construction performance, strong adhesion between substrate and surface coating after coating is dried. Besides, this coating also has good alkali resistance and water resistance. What’s more, this paint is non-toxic and safe.

Typical Uses:

This product is designed for the intermediate aggregate which needs to form a concave and convex coating such as the industrial plant, civil or public building walls, ceiling and asbestos board.

这里可以自定义设置

Application Guide

● Mixing:

Ready to use.

● Thinner:

Clean water

● Airless spray:

Spray 0.6m/min pressure: 0.3~0.6 MPa

Nozzle tip diameter:4-10mm, after touch dry, use a smooth

rubber roll to flatten the convex surface

● Brush, Roller:

Recommended to be used with spraying

● Scraping:

Recommended

DRYING SCHEDULE

Substrate temperature	10°C	20°C	30°C
To touch(1mm)	8h	4h	3h
To handle(1mm)	36h	24h	20h
Min. recoating time	36h	24h	20h
Max. recoating time	-	-	-
* Make sure no chalking and other contaminations before recoating.
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation conditions, humidity, mechanical strength,etc.

这里可以自定义设置

SURFACE TREATMENT

Surface treatment of each base course: the quality of the cement slurry and concrete base

course shall conform to JGJ73-91 code for construction and acceptance of building decoration engineering. The base surface must be clean, dry, firm, free of grease and other dirt, with a PI value less than 10. For walls with old besmear film, if the film is loose, falling off and pulverized, it should be cleaned up, polished with sandpaper. In case of mildew on the wall, wash it with hot water containing 25% bleach. Leave the washing solution on the surface for 10 minutes. Then rinse the surface thoroughly with clean water. Dry it for 48 hours before applying. The surface and gap should be fixed with the company's construction paint special putty. The treated wall should be constructed as soon as it is dried, so as to avoid re-pollution.

APPLICATION

Application conditions: Substrate temperature shall be 3 ℃ higher than dew point with relative humidity below 85%. Measurement of temperature and humidity should be conducted close to substrate.

这里可以自定义设置

CLASSICAL COATING SYSTEM

Please inquiry JIANBANG Paint for specific coating solutions.

Classic Coating System

Advanced Construction Latex Coating Sealing Primer

1*20 µm (dry film thickness)

Advanced Exterior Wall Putty

1~2 mm (dry film thickness)

Advanced Construction Latex Finish Paint

2*60 μm(dry film thickness)

这里可以自定义设置

SAFETY AND HEALTH

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. The coating is a water-based coating. Water-based solvent has mild eye irritation, upper respiratory tract irritation, long-term close contact with dry skin, etc. Proper ventilation and precautionary measures must be in place. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

Please handle used paint barrel correctly to avoid any pollution.

Storage:

Store this product in shady, dry, and ventilated warehouse. The shelf life is 6 months at room temperature. If exceeding shelf life, the products shall be tested before using.

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.