Oriented by technology, we serve customers worldwide not only our high quality products, but also technical consultation and engineering scenarios.
PRODUCT DESCRIPTION
This product is composed of exclusive putty polymer, auxiliaries and white cement. The putty layer is provided with great resistance to alkali and water. Furthermore, with great adhesion to substrate, this paint is easy to apply, non-toxic and safe to use.
Typical Uses:
This product is typically used to repair the edges of inner or outer walls based on concrete, cement mortar, and bricks. Meanwhile, it is also able to be used to fill the pits and fissures of that substrate.
Application Guide
The quality of cement mortar and concrete base shall conform to JGJ73-9Construction acceptance code for architectural decoration engineering. With the PH value less than 10, the base surface must be clean, dry, solid and free from oil and other dirt. In case of old coating film wall, the loose, detached and powdered coating shall be removed. Besides, the surface shall be smooth by burnished. In case of wall with mildew, wash the wall with hot water containing 25% bleach, and leave the detergent on the surface for 10 minutes. Then rinse the surface thoroughly with clean water, and coat it after drying for 48 hours. In addition, use the exclusive putty for construction materials from the company to fill the gap and smooth the rough surface. Furthermore, please paint after the wall is dry as soon as possible to avoid re-contamination.
● Time of recoating:
Min. 3h
● Thinner:
Clean water.
● Coating interval:
Minimum 3h.
● Next matching:
Using the advanced construction latex coating sealing primer.
● Tool cleaning:
Clean water.
SURFACE TREATMENT
Surface treatment of each base course: the quality of the cement slurry and concrete base course shall conform to JGJ73-91 code for construction and acceptance of building decoration engineering. The base surface must be clean, dry, firm, free of grease and other dirt, with a PI value less than 10. If have the metope of old besmear film, answer will loose, fall off, the besmear film that powdery is cleared clean, grind with sandpaper level off. In case of mildew on the wall, wash with 25% bleach in hot water. Leave the washing solution on the surface for 10 minutes. Then rinse surface thoroughly with clean water, surface should dry for 48 hours before applying. The surface and gap should be coated with the company's construction materials special putty wipe flat. After the treatment of the wall, the wall should be dry as soon as possible after the construction, so as to avoid re-pollution.
Construction Latex Coating Sealing Primer: 1*20µm (dry film thickness)
Building Paint Exclusive Putty: 1~2mm (dry film thickness)
Advanced Construction Latex Coating Finish Paint: 2*60µm (dry film thickness)
SAFETY AND HEALTH
Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.
Please handle used paint barrel correctly to avoid any pollution.
Storage:
Store this product in shady, dry, ventilated and away from heat sources warehouse. The shelf life is 3 months at room temperature. If exceeding shelf life, the products shall be tested before using.
Disclaimer:
All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.
Packing size | Packing weight |
20L | 25 KG |
Copyright © 2020 Changzhou IMS New Materials Technology Co., Ltd. | All Rights Reserved | XML
Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.