Industrial Functional Epoxy Floor Paint

这里可以自定义设置

PRODUCT DESCRIPTION

Epoxy floor coat is two parts amide cured epoxy that designed to give a chemical resistant, durable and hard wearing surface on a concrete floor. Also, it combines incredible hardness and bonding power to provide a heavy duty and to be used as topcoat. The main advantages of epoxy floor coat are immensely tough, fast curing, virtually odour free, chemical resistant, easy to clean and non-flammable.

Typical Uses:

This product is designed for a wide range of floors with various levels of mechanical and chemical exposure. It is also used to protect materials on substrate like concrete floors in workshops, factories, warehouse, garages and etc. The idea is for internal use only. It will cause yellowing and deterioration of the paint film over time when exposure to direct sunlight.

这里可以自定义设置

PRODUCT SELLING POINT

● The epoxy floor paint is mainly prepared by epoxy resin, curing agent, dispersant and aggregates depend on requirements.

● Main advantages of this paint are great resistance of slippery, electrostatic, acid and alkali.

● Moreover, it also has good resistance to organic solvent, heavy load and abrasion.

● Besides, it combines incredible hardness and bonding power to provide a heavy duty and to be used as topcoat.

PRODUCT ADVANTAGES

Extend the service life by 2-3 years

Resistance (chemical medium) 98% sulfuric acid, 30% hydrochloric acid carefree

Five years bright as new, 5.99% Improve the yield of sensitive devices by 99%

50% Avoid slips and increase safety by 50%

这里可以自定义设置

PRODUCT PARAMETER

Technical Details	Color	Choose from the color card	Application Guide	Mixing	Stir the part A evenly by power mixer then add hardener until fully mixed. Generally, if the temperature below 10 ℃, it needs 30 min induction time; if the temperature over 10, it needs 15 min induction time.
	Gloss	(35-75)Glossy
	Coverage	5 to 8 sq. meters per litre
	Solid Volume	50±2 %		Mixing Ratio	Part A: Part B= 20:5 (by weight)
	Film thickness	DFT: 40-60µm (WFT: 80-120µm)		Thinner	X-7 Epoxy Paint Thinner
	Theoretical spreading rate	12.5-8.3m²/L		Airless Spray	Nozzle tip: 0.021~0.025 inch
	Full cure	7d			Spray pressure: 15~18 MPa
	Flash Point	25 ℃			Thinner ratio: 0~10% (by weight of paint)
	Shelf Life	12 months in sealed container		Brush、Roller	Recommended for small areas only. Must achieve required thickness.
	Ready for foot traffic	After 24 hours		Brush、Roller

MORE SPECIFIC COLORS PLEASE CONSULT US

DRYING SCHEDULE

Substrate Temperature	10 ℃	20 ℃	30 ℃
To touch	4h	2h	1h
To handle	24h	12h	6h
Min. recoating time	16h	8h	4h
Max. recoating time	10d	7d	5d
Pot life	4h	2h	1h

* Make sure no chalking and other contaminations before recoating

* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation conditions

PRODUCT SPECIFICATIONS

Color	Customized
Gloss	Glossy
Density	~1.3 Kg/L(after mixing)
Hardness	Epoxy paint curing agent
Solid volume	(50±2) %
Film thickness	100&µm dry film thickness (about 200&µm wet film thickness)
Theoretical spreading rate	3.8m²/Kg (100&µm dry film thickness)
Full Cure (23±2℃)	7~15d
Flash Point	31℃

这里可以自定义设置

PRODUCT APPLICATION

Substrate temperature shall be at 3 ℃ higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.