Jb Epoxy Paint-101

这里可以自定义设置

PRODUCT DESCRIPTION

This two-component sealing primer is mainly prepared by epoxy resin and curing agent, with outstanding features as below:

● Permeable to substrate

● Sealing property

● Resistance to alkali, acid & water

● Good Adhesion

● Excellent rust resistance

● Outstanding sea water resistance

● Continue to cure when immersed in water

● Etc

Typical Uses:

This product is typically used as metal surface . Commonly used for coat for:

● Port

● Steel

● Harbor

● Pipe

这里可以自定义设置

Instructions for Use

Mixing

Mix part A and part B as 20:5by weight. Slowly add part B into part A and

ensure mixed completely.

● Thinner:

Epoxy paint thinner ≤ 10 % w./w.

● Cleaner:

X-7 epoxy paint thinner

DRYING SCHEDULE

To touch/H	3H
Overcoating	M:3.5H
Thickness	1mm
Color Variation	Color may vary from batch to batch. JIANBANG ensures color variation ∆E≤0.2. Suggest use the same batch to achieve best color consistency.
Packaging	Part A 20 kg in an iron barrel Part B 5 kg in an iron barrel.
Pot life	Part A 12 months, Part B 12 months
* Make sure no chalking and other contaminations before recoating.
* Above data for reference only, actual drying time and recoating time is dependent on temperature, dry film thickness, ventilation condition.

这里可以自定义设置

SURFACE TREATMENT

All surface to be coated shall be clean and dry. The surface shall be evaluated and treated according to ISO8504 standard.

Steel: Sanding to Sa2.5 (ISO8501-1:2007). It is acceptable to polish by power tools to meet at least St2.0(ISO8501-1:2007).

Concrete surface treatment:

a. First of all, it is necessary to confirm whether reliable damp-proof facilities are installed below the concrete base. The new concrete or cement base should be cured for at least 28 days, and its moisture content should not exceed 5%. The moisture content of the base should be evaluated by empirical method.

b. The base surface should be clean, solid and pollution-free, such as slurry and paint splashing, curing agent, grease and so on. For excessive float pulp, it is better to first use slight roughing, polishing, oil-stained ground, using electric angle grinder to polish.

c. The cracks and empty drum on the floor surface should be repaired first.

d. Whatever method is used to treat the surface, a clean, solid and dry base surface must be obtained. It is especially important that the grassroots should not be in a state of rising tide.

e. The base layer is cleaned and sanded with a sander.

APPLICATION

Application conditions: Substrate temperature shall be at 3 ℃ higher than dew point, relative humidity less than 85%. Measurement of temperature and humidity should be close to substrate.

这里可以自定义设置

CLASSICAL COATING SYSTEM

Please inquiry JIANBANG Paint for specific coating solutions.

Epoxy Sealing Primer: 1*30 µm (dry film thickness)

Epoxy Putty: 1~2mm (dry film thickness)

Anti-static Floor Paint: 100 µm(dry film thickness)

这里可以自定义设置

SAFETY AND HEALTH

Please refer to MSDS before using this product. If you do not fully understand the restrictions, or cannot follow MSDS directions strictly, do not use this product. This volatile product is flammable. Keep this product away from flame or fire. Smoking is strictly prohibited in working area. Keep working area ventilated during application to make sure solvent vapor content is low in the air. PPE is necessary to avoid this product contacting with eyes or skin. More detailed safety tips are based on practical situation.

Please handle used paint barrel correctly to avoid any pollution.

Storage:

Store this product in shady, dry, and ventilated warehouse. The shelf life is 12 months at room temperature. If exceeding shelf life, the products shall be tested before using.

Disclaimer:

All technical data given in this document is based on our knowledge achieved in lab and practice, it is not completely correct. Although we try to keep the validity of our advice, however we cannot predict the practical conditions that will affect paint quality. Herein, we cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions. We reserve the right to modify this document without informing in advance.